Who Owns the Tech Pack and Patterns?

Who Owns the Tech Pack and Patterns?

Ownership and handover

Who Owns the Tech Pack and Patterns?

The buyer owns the tech pack if the buyer authored it or paid a development fee for it, and the factory owns the base blocks it developed independently. A style pattern made specifically for your design normally belongs to you once the development fee is settled, but only if the order confirmation or development agreement names the pattern, the graded nest and the marker as deliverables. Ownership without custody is worthless in practice, so the same document should state which file formats are released, within how many working days, and on what trigger.

Tech pack: buyer Style pattern: buyer if paid Base block: factory Release: 5 working days

The Answer in Three Sentences

What you authored stays yours

Sketches, measurement charts, construction notes and artwork you created before approaching a factory are your work product. No clause is needed to confirm it, though a clause helps when you have to prove it.

What was made for you transfers on payment

A style pattern, graded nest or marker developed for your garment transfers when the development fee is paid, provided the purchase order or development agreement lists it as a deliverable.

What the factory built for itself stays with it

Base blocks, machine settings, internal sewing sequences and general know-how belong to the factory. Asking for a block is asking for the factory's tooling, and a refusal is reasonable.

What "the Tech Pack" Actually Covers

The question sounds simple until a dispute starts, because a tech pack is a bundle of documents rather than one file. Factories routinely release part of the bundle and hold the rest, so it helps to know which part you are arguing about.

  • Design specification: flat sketches, detail callouts, stitch types, topstitch distances, placement diagrams. Authored by the buyer in almost every case.
  • Measurement specification: points of measure, base size values and tolerances. Buyer-authored, but often revised with factory input, which is where shared-authorship claims begin.
  • Construction sheet: seam types, seam allowance, hem finish, interlining, fusible placement, pressing parameters. Frequently co-authored, and therefore the item factories most often treat as their own document.
  • Bill of materials: fabric, lining, thread, trims, labels, packaging. Yours, though supplier names inside it may be redacted as commercial information.
  • Pattern package: base pattern, graded nest, marker, seam allowance layers. The contested item in most handovers.
  • Artwork and print files: repeat size, colour separations, placement. Yours if you supplied the art; licensed if a studio created it under its own terms.
  • Approval records: lab dips, strike-offs, bulk approvals, shrinkage test results. Valuable because they encode decisions that are expensive to repeat.

If you are still building the document itself, our guide to tech packs for linen clothing sets out what a factory needs before it can quote accurately, which is also the shortest route to a documented file list you can point back to later.

Pattern, Block and Marker: Three Different Assets

Most confusion comes from calling three separate objects "the pattern". They have different owners by default and different value to your program.

AssetWhat it isDefault ownerWhat to ask for
Base blockFactory's working pattern for a shirt, dress or trouser, refined over yearsFactoryNothing. Ask instead for a style pattern drafted on it
Style patternThe block modified to your neckline, shoulder, hem and pocket placementBuyer, if development was paidNative CAD file plus DXF plus 1:1 PDF plot
Graded nestThe style pattern across the full size range, with grade rulesBuyer, if included in the feeNest file with shrinkage allowance documented
MarkerCutting layout optimising fabric consumptionBuyer, where cutting is paid forMarker file plus consumption per size
Cutting die or screenPhysical tooling made for your styleBuyer, if paid by buyerPhysical delivery at buyer cost

In linen programs, the nest deserves extra attention: first-wash shrinkage commonly runs 3 to 7 percent and differs between warp and weft, so the nest must arrive with its shrinkage allowance recorded, not only with pattern geometry.

How to Write It Into the Contract

General statements about intellectual property fail in specific disputes. "All IP remains the property of the buyer" invites the objection that a pattern is a tool, not intellectual property. Replace the principle with a list and a trigger.

1
Name the files. List tech pack, measurement chart, style pattern, graded nest, marker, artwork, print files, lab dip and shrinkage records individually. Named deliverables are enforceable; categories are arguable.
2
Name the trigger. "Within 5 working days of written request, and automatically on settlement of the development fee" replaces "upon request", which gives an open-ended timeline and no obligation to prioritise you.
3
Name the formats. Native CAD file, exchange file such as DXF or ASTM, and a 1:1 PDF plot for physical verification. Vector artwork with fonts outlined. Machine files plus placement diagrams for embroidery and prints.
4
Name the prohibition. No production of the style, and no derivative version with minor changes, for any other party, for a stated period after the last shipment, binding subcontractors and successors.
5
Name the survival. Ownership, confidentiality and tooling terms survive termination. Without a survival clause, the obligations end when the relationship does, which is exactly when you need them.

For a clause-by-clause review beyond ownership, see our notes on linen manufacturing contracts. For the confidentiality side specifically, protecting your designs with a linen manufacturer explains why an NDA restricts disclosure but not production, and what to add so it does both.

The trigger is the clause that changes behaviour

A factory asked to release files "on request" has no deadline. A factory obliged to release within five working days of a written request, and automatically at payment, has a deadline and a reason to keep the files findable. Most buyers never receive their patterns because they never set that obligation, not because the factory refused.

Switching Factories: What to Request

When a program moves, the request should be a list rather than a conversation. Ask for these items in one email, referencing the purchase order number and the development fee paid.

Tech pack in its final approved version, not a superseded draft
Measurement chart with tolerances per point of measure
Style pattern in native, exchange and plotted formats
Graded nest with grade rules and shrinkage allowance noted
Marker file and fabric consumption per size
Shrinkage test results by direction, plus the wash recipe used
Fabric reference: mill, article number and a physical swatch of the lot used
Lab dip and bulk approval records, with the light source used for assessment
Style-specific operation list, even handwritten
Retained reference sample, or detailed photographs of inside seams and finishes

Two items on that list are routinely forgotten and cause the most drift after a switch: the shrinkage record and the operation list. A new factory can draft a pattern from a garment, but it cannot guess which wash cycle produced the original hand-feel, and it will not reproduce a collar roll without knowing the interlining and pressing sequence that created it.

Formats That Survive a Switch

Native CADEditable pattern and grade rules. The only format that allows real rework.
DXF or ASTMPortable geometry between CAD systems. Grade rules may need rebuilding.
1:1 PDF plotPhysical verification. Proves the file matches the approved sample.
Vector artworkPrint and embroidery files with fonts outlined and colour separations included.
Structured specMeasurement and BOM data in a spreadsheet, not only inside a PDF.
Photo recordDetail shots of construction, labels and finishes, dated and linked to a sample.

When a Freelance Pattern Maker Is Involved

A large share of style patterns are not drafted inside the factory at all. The factory engages a freelance pattern maker, sends your measurements and receives a DXF in return. In that chain, ownership depends on the engagement between the factory and the pattern maker, which you are not party to. If that agreement assigns the deliverable to the factory, the factory holds the file and can decide whether to release it. If it retains rights with the pattern maker, even a willing factory may be unable to hand it over without consent.

The practical response is to ask who drafts the pattern before the development fee is agreed, and to make that answer part of the purchase order. Where an external pattern maker is named, add a line requiring the factory to obtain a written assignment of the deliverable to you, or to commission the work under your own name. The cost difference is usually small, and it removes an entire category of delay later.

The same logic applies to grading. A pattern may be drafted in-house while the nest is graded by a separate specialist, which means two files with two sets of terms. Ask for both, and ask which party holds the grade rules, because a nest without editable rules is only marginally better than a plot.

Where Buyers Lose Control

Development absorbed into the sample fee. If pattern making was free, there is no payment trigger and no contractual reason to release anything.

No canonical file. Approval by email leaves forty versions and no master, so the factory's last internal copy becomes the reference by default.

PDF-only delivery. You can see the pattern but cannot edit the grade, so the nest is rebuilt and fit drifts at the hip or armhole.

Unnamed subcontractors. A satellite workshop that sewed your style during peak season holds a copy and owes you nothing, because the contract named only the main factory.

Derivative production. A supplier that cannot copy the style exactly may still produce a similar garment using your neckline and pocket placement. Naming derivative versions closes that gap.

If You Have Already Lost the Files

Recovery follows a predictable order, cheapest first.

  1. Ask formally, once, referencing the order number and the development fee paid.
  2. Offer to cover retrieval, plotting and courier costs, which removes the only legitimate objection.
  3. Accept a partial release if the pattern is refused, since charts, construction notes and lab dips still cut redevelopment time.
  4. Settle with an external pattern maker where the factory does not hold the rights, which transfers the file permanently.
  5. Rebuild from a retained sample only when the first four routes close.

Even a partial release resolves a surprising share of cases, because a written request with a reference number reaches the person who can actually find the file. Where the factory paid an external pattern maker, a modest settlement can transfer the file permanently.

If nothing is released, rebuild from a retained production sample: digitise the pattern, confirm measurements after one wash so the 3 to 7 percent shrinkage is accounted for, and run one verification round at the new factory. Budget three to four weeks before bulk, and plan a second round rather than assuming a first-time match. The sampling rounds guide explains how to structure that verification so it does not expand into three rounds of redesign.

Buyers who recover quickly share one habit: they asked early, in writing, while the relationship was still commercial. Buyers who recover slowly waited until after the final shipment, when the factory had no commercial reason to prioritise the request.

Related Questions

Does paying for a sample give me the pattern?
Not automatically. A sample fee covers materials, labour and shipping. Pattern ownership depends on whether a development or pattern-making fee was charged and what the order confirmation names as deliverables.
Can a factory refuse to release my style pattern?
It can refuse its base blocks, which are its own tooling. A style pattern developed for your design and paid for by you is harder to justify withholding, but proving that requires the document trail.
Is an NDA enough?
No. An NDA restricts disclosure, not production. You also need a clause prohibiting manufacture of the style or a derivative for other parties, binding subcontractors, for a defined period.
How long should a handover take?
Exporting existing files takes days. Five working days from a written request is a fair contractual window; longer usually means the files must be rebuilt or are being used as leverage.
Settling ownership before the first deposit

If you are preparing a linen program, send your tech pack and target quantities and we will confirm what is delivered, in which formats, and on what trigger. Technical review comes back within 48 hours and a costed quotation within 3 to 7 working days, with MOQ at 60 pieces per style per colour, sampling at 7 to 12 days and bulk at 25 to 35 days.

Scope note: this answer describes ownership practice for cut-and-sew linen programs in the 60 to 5,000 piece range, based on how development fees, sampling and bulk orders are structured at Linenwind. Contract terms differ by jurisdiction; the wording here is commercial practice, not legal advice. Linenwind is a Dongguan-based linen garment manufacturer working to ISO 9001, OEKO-TEX Standard 100 and SEDEX standards, with AQL 2.5 inspection and a 50 plus article fabric range in stock.